Product Search
Search results for 'C-234'
Showing 61 - 81 of 563 Total Results
Curing Rack, 4" x 8" Cylinders 12/ctn
CA-0219
Location: Parts & Accessories
These durable racks are manufactured from plastic compounds and recycled materials to resist moisture, abrasion, chemical and temperature variations. Each rack has built-in handles, making them easy to carry and safely stacked 12 tiers (58") high. The racks unique open frame design allows water...
(4) options
Location: Test Platens
Test both cubes and cylinders . Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
(2) options
Location: Vebe Consistometer
The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete - from Test Mark Industries.
(41) options
Location: Air Meter Replacement Parts
Concrete air/pressure meter replacement parts are available from Test Mark. Use our diagram to find the part you need for easy online ordering.
CA-2560
Location: Sample Splitters
The adjustable sample splitter from Test Mark reduces aggregates to a suitable size and amount for gradation testing.
CA-0500-42
Location: Air Meter Calibrators
Brass reusable calibration vessel can be used with any 1/4 cu. ft. concrete pressure meter. Vessel is exactly 5% air by volume when placed in the pressure meter base. Part of our air meter calibrator products.
(3) options
Location: Beam Testers
Self-contained shock-proof portable concrete beam tester accurately and easily determines flexural strengths of 6 x 6 in. cross-section beams - from Test Mark.
CA-1450
Location: Gloves
Test Mark's heat resistant gloves are used for handling heated items when conducting laboratory work with ovens or hot plates.
SA-1150
Location: Shelby Tube Permeameter
The Shelby Tube Permeameter from Test Mark allows you to perform permeability tests on undisturbed soil samples.
AA-0010
Location: Marshall Basic Compression Testing
The lower segment of Test Mark's Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments.
AA-0011
Location: Marshall Basic Compression Testing
The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.
CA-2165
Location: Clean-N-Weigh
The Clean-N-Weigh accessory offers the fastest and most efficient method of processing large, coarse aggregate samples for particle size tests.
CA-2700
Location: Specific Gravity Flasks
The Chapman flask from Test Mark has two bulbs for determining approximate percentage of voids and surface moisture in fine aggregates.
CA-2570
Location: LA Abrasion
The LA Abrasion Machine from Test Mark tests crushed rocks, slag and gravel for resistance to abrasion.
Spacers for CM-0030 and CM-2500 series
(4) options
Location: Spacers
Spacers are used with test platens to adjust the vertical working clearance height inside a machines load frame, for testing samples of various types and sizes to prevent over-extension of the load frames piston. They are manufactured from steel and machined plane on both ends to maintain a...
(3) options
Location: Test Platens
Models available for testing 12” (305 mm) and 8” (203 mm) wide masonry units. . Both models feature large diameter spherical disk and seat assemblies, and platen bearing surface plane to .001” (.025 mm) in any 6” (152 mm) direction, through hardened to HRC 60 and plated for wear and corrosion...
Biodegradable Extraction Solvent
(2) options
Location: Biodegradable Extraction Solvent
Excel Clean HD Biodegradable Extraction Solvent is approved by many state DOTs for centrifugal and vacuum asphalt extraction tests.
Dynamic Cone Penetrometer only
SA-1225
Location: Dynamic Cone Penetrometer
The Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20" and can be used effectively in augured holes to depths of 15 to 20 feet. The DCP features a heat treated cone and zinc plated components.
(2) options
Location: Cylinder Canvas Wraps
Neoprene pad inserts from Test Mark are made from a tough elastomeric material that evens out and fills irregularities in the ends of concrete cylinders to assure even distribution of test loads for consistent results.
